Forklift repairs

11 462
261
 
Working on a traverse lift 6035 shooting boom fork lift. Installing a new seat, starter, tilt gauge, fork tilt switch, oil change, and removing/installing the main lift cylinders.
Motor
Runtime: 55:09

Kommentarer

Jake
Jake - 21 time siden
that dog is so fucking cute
Larry Baker
Larry Baker - Dag siden
Andrew I'm gonna tell you why it was so hard to remove and install the cylinder, the bushing is a (Mandrel) type that's why the nut was small than the eyelet, when you tighten the nut it pushes in to expands to hold the cylinder in place, it should had decompressed when you removed the nut but when you forced it off it stayed in the expanded position. It's a compression bering.
Vincent Devaux
Vincent Devaux - 2 dager siden
23:35 video start here
mynamesmike88
mynamesmike88 - 3 dager siden
28:28 thats it!
Harold Butt
Harold Butt - 4 dager siden
While watching I was wondering ? when did he get chickens? lol.
telosfd
telosfd - 8 dager siden
At 39:00 looking with eye it is not square soldering. I like your try!
Rick Bueche
Rick Bueche - 8 dager siden
Cody said "While Andrew works on his big orange fork lift, I am going to work on this big orange drink cap." LOL.
Blaine Bugaski
Blaine Bugaski - 10 dager siden
Almost as if those bushings should have been stuck to the rams rather than the spindles.
Donny Thomas
Donny Thomas - 11 dager siden
you're a cool dude man...
xxshadowninja xx
xxshadowninja xx - 12 dager siden
Oh, I cringed when you put the cylinder back over the bearing on the boom.
William Malenfant
William Malenfant - 12 dager siden
Not pretty but it works and you saved at least $600.00. Kudos Andy!
Livin da life
Livin da life - 13 dager siden
Next addition you need a dedicated shop air compressor and solar. What happened to Levy?
Joe Barton
Joe Barton - 13 dager siden
Fair play ! If u can’t loosen something with the biggest wrench you got, or the biggest sledgehammer, or a bar or a wedge.... simply get your 10 ton excavator and stick the half ton bucket through the door to your workshop and just pull it off! It’s that simple. Brilliant
John DiPetrillo
John DiPetrillo - 14 dager siden
“That how u do it right there, read this in the manual “
Richard H Jones
Richard H Jones - 16 dager siden
You should take on the rebuilding of the cylinders have done several over the years. They are not that hard to do. And I have been watching you on this channel for a couple of years and have no doubt you could do it with no problem. You might need to get a few specialty tools but other than that you could do it no problem.
Mike Spain
Mike Spain - 17 dager siden
$725 bucks for a new joystick, and $300 bucks for a level. Only rich people that can't think outside the box would pay those prices. This includes any government run organization with equipment. Nothing but the best when the taxpayer is buying. Great video. Buy more tools when you have to complete a job, I know the feeling.
TIm Nash
TIm Nash - 18 dager siden
Tim from Canada suggestions what you can use a counterweight on the back of your left or do with the farmers do load up your tires you can buy pre-loaded tires for tractors if they are light do you not know if you can buy loaded tires .. for this I know Kabota and a few other places they lowered their tires if machines are too light just my suggestion anyone out there have another solution to this feel free to add your comments to the bottom or suggest something else
clay longest
clay longest - 19 dager siden
I really dont understand why he uses craftman drills.
Mainmanrr
Mainmanrr - 22 dager siden
Wait, what? Andrew cant rebuild cylinders. That's the first time he cant fix something. He can patch a mountain thou.
Cookie's House Cannabis Co
Cookie's House Cannabis Co - 24 dager siden
Andrew:
Levi:
Cody: AWARROO AROO AROOOOOOOO
Bernard Grubb
Bernard Grubb - 24 dager siden
reassembly would have been much easier if he had just started the machine and wiggled the cylinder into place. He made a lot more work and went to a great expense unnecessarily.
flyrock45
flyrock45 - 24 dager siden
Why didn't you bring it to the same place that rebuilt the alternator for the Ford dump truck?
Russian Spy
Russian Spy - 25 dager siden
It is not coming off gets a digger aka the persuader
Dean Farmer
Dean Farmer - 25 dager siden
44:12 uses a flywheel puller on a hydraulic cylinder
Dusty 99
Dusty 99 - 17 dager siden
Wow! What do you do for an encore?
Dean Farmer
Dean Farmer - 25 dager siden
31:20 smart idea what you did on the second floor
Dean Farmer
Dean Farmer - 25 dager siden
that dog sure does like Gatorade
Bruh with a Chevy
Bruh with a Chevy - 25 dager siden
1:11 Andrew looks like he’s stealing it
William Hayes
William Hayes - 26 dager siden
$307 for a level gauge!!!! WTF!!!
Sue Anderson
Sue Anderson - 26 dager siden
Where is Levi??
The Stone Mason.
The Stone Mason. - 26 dager siden
That's a great repair to the joy stick if you just use it yourself, but if did that for a paying customer, they would sue even if it worked fine. Hence the inflated prices from the repair shop. 😀
Alexei Tetenov
Alexei Tetenov - 26 dager siden
Andrew, thank you for creating such an entertaining channel and videos. I will probably never work on such heavy machinery but I was so fascinated by the video. :-)
Alexei Tetenov
Alexei Tetenov - 26 dager siden
46:38 - Attaching lower bolt. Maybe Andrew should have put the top bolt on, before the lower bolt, so that it was free to swing a little bit, enough to align perfectly... So that he would not have needed open up the upper "bolt hole"...
TeddyJak Eddy
TeddyJak Eddy - 26 dager siden
"That's how you do it. I read it in the manual." How many of us are going to steal that line?
Paul Caslin
Paul Caslin - 27 dager siden
Tremendous video but warm the ram eye freeze the spigot ?
Carl Peterson jr
Carl Peterson jr - 28 dager siden
where is Levi .
wayne goff
wayne goff - 28 dager siden
Bet the guy who sold it will be sick if he watches this video.
wayne goff
wayne goff - 28 dager siden
@Andrew Camarata I wonder if he asks you to do his repairs.
Andrew Camarata
Andrew Camarata - 28 dager siden
He bought a new one.
Barbara Collins
Barbara Collins - 28 dager siden
I havnt turned the TV on for many days......lol
Jason Laughrey
Jason Laughrey - Måned siden
Suggestion, if you heat it in one spot with a torch it will expand make it a lot easier to go on. Hope this helps for the next time.
Ruben Kelevra
Ruben Kelevra - Måned siden
27:10 wait, why didn't you pull it off there?
Just put some washers below the nut and tight it again. That's why there's so much thread 😁
alharbi aljazee
alharbi aljazee - Måned siden
Good work, remarkable effort, but a joy to watch
William Lyerly
William Lyerly - Måned siden
I kept waiting for the ritual touch up painting. Maybe at 4,000 hours.
Dennis Dubey
Dennis Dubey - Måned siden
Love your projects. Can you give us a complete tour of your house, shops & property?
Tamas Takats
Tamas Takats - Måned siden
Andrew,is there anything out there you don’t know? You are one smart man, God bless you...
Cole Atkins
Cole Atkins - Måned siden
cole atkns
billiebob123456
billiebob123456 - Måned siden
WHAT ABOUT AIR ANF FUEL FILTER S
billiebob123456
billiebob123456 - Måned siden
OHHHH EINSTEIN THE REASON FOR NO WASHER ON THE OUTSIDE IS THAT BRASS BEARING IS MADE TO SWIVEL AND TILT A LITTLE BUT YOU KNEW THIS ANYONE WITH A BRAIN WOULD OF CALLED TO JUST HAVE A MECHANC OR GO ON LINE TO READ THE WAY THAT WOOD BEAT THE PUMP AND NO ONE CHECKED IT IS WORSE
billiebob123456
billiebob123456 - Måned siden
DUDE I WOULDN`T LET YOU LOOSE WITH BOB THE BUILDER TOOL SET YOU ARE SCARY YOU DIDNT USE A MICHROMETER IN THE BOLT OR THE PUMP WOW YOU ARE SCARY
billiebob123456
billiebob123456 - Måned siden
GOOBER WHY DIDNT ANYONE CHECK THE BOLT TO SEE IF A NEW ONE THAT WASN`T HAMMERED AND BEAT ON CAUSE YOU DIDNT USE A PULLER OR NOW A BLOCK OF WOOD THE BEARING OR THE BOLT ARE USELESS
billiebob123456
billiebob123456 - Måned siden
WHY DIDNT YOU GO BUY TWO OR THREE A SPARE LOCKING NUTS CAUSE WHY ???? ONCE THEY ARE TORKED DOWN THEY ARE USELESS OR BECOME SPARES ???? YOU CAN`T BE THAT CHEAP ??????????????
billiebob123456
billiebob123456 - Måned siden
HEY MR HEINY WHY NT GO TO GOOGLE AND ENTER THE TRACTOR AND SEE IF AND WHAT THEY CAN TELL YOU ?????? WHY NOT GET A FORK SPLIT IT IN BETWEEN OR A PULLERS AND SCREW IT LIKE A BEERING IN A CAR OR TRUCK AND NOT BUTCJ=HER ANY MECHANIC CAN LOAN YOU A MEDIUM OR LARGE WHEEL PULLEDR
Agent Bertram
Agent Bertram - Måned siden
Andrew, I have discovered that we have something in common. Our love of heat shrink sleeving.
Did you know that you can get heat shrink in large sizes too? I have a size that could slip over the joystick that you put the ATV switch on, which would make the repair look "extra professional".
I got mine on ebay.
ALI BUOLAYYAN
ALI BUOLAYYAN - Måned siden
I love your job, I like to work with you
Marcos damaceno
Marcos damaceno - Måned siden
Cool Cody drinking gatorade. kkkk
Alex Goldstein
Alex Goldstein - Måned siden
Good Job man, its always an uphill battle with this kinda stuff.
juliorx
juliorx - Måned siden
What is your education? How did you learn to do all these repairs. It is amazing how you can figure all this out. Thanks
Floyd Cauley
Floyd Cauley - Måned siden
You need a Kubota to fix everything else !
Apollo
Apollo - Måned siden
@12:15: "They wanted $725 for that part, so we're going to fix it for like $15 instead"
Phillip Ryder
Phillip Ryder - Måned siden
I believe the bushing on the cylinder and the cylinder eye are tapered. The eye got rotated during the re-build.
Wade Lasch
Wade Lasch - Måned siden
It was probably tapered! That’s what it didn’t go on right
Wade Lasch
Wade Lasch - Måned siden
Probably should have flipped it around
Wade Lasch
Wade Lasch - Måned siden
Great work! Get a bigger sprocket on the lift tho to make it lift faster
Mike Bowhunter
Mike Bowhunter - Måned siden
The more I watch, the more I like this guy! The washers allow the ram end to pivot..
oldmantex
oldmantex - Måned siden
Don't sacrifice safety Andrew!! Good job on the seat belt. Much safer in the machine that getting squashed outside. We had a couple guys roll over and the seat belt saved their bacon.
Hermann Froh
Hermann Froh - Måned siden
Put a handmade leather jacket around that controller and it looks quite nice and expensive, too. ;)
TEJ Jensen
TEJ Jensen - Måned siden
Over $ 700 and ebay 10. Sometimes it's the wrong people who fill our prisons!!!
Sam B
Sam B - Måned siden
Andrew where did you get some much money to purchase all of this equipment?
Mark Stephenson
Mark Stephenson - Måned siden
Back in 1990 I bought a D8 Cat and dug a 10 acre lake. Was 32 years old then. The cat was a 1964 D8 H hydraulic with a pony motor.
I totally rebuilt the carriage ,made a line boring machine to line bore the carriage roller fits with caps, wrap welded the rollers, installed new bearings and seals in the rollers and last but not least rebuilt the pony motor. I KNOW EXACTLY WHAT YOUR GOING THROUGH!!!! Love your videos!!
Joe McMullin
Joe McMullin - Måned siden
I'm jealous. Would be awesome to have one of those. I was browsing and even the ghetto old ones with like 5k hours on them are still expensive af.
Proud American
Proud American - Måned siden
That's how you do it right there, I read this in the manual: LMAO! I like your style :)
JACK CONNOR
JACK CONNOR - Måned siden
I like his get it done approach to everything. I would not be surprised if this thing gets sold as soon as the Castle is finished
Otto Carr
Otto Carr - Måned siden
He doesn’t need to know those things are called “brushes” to make the starter work better. He is an intuitive mechanic. Impressive!
Mark O'nee 1
Mark O'nee 1 - Måned siden
Next time you repair a control lever buy some carbon fibre look heat shrink tube they sell to repair fishing poles and pimp your rides levers ..Your machine's weird in not having the front stabilisers fitted but it's got the cab sway ? .First one ive seen like this as the stabilisers are needed to eliminate any swaying and take the weight off the wheels to level the machine out when lifting ! .
Lorraine Helt
Lorraine Helt - Måned siden
I just sit here with a big smile on my face. What a guy !!!!!
Ben Johnson
Ben Johnson - Måned siden
You need to learn how to bench test before putting the starter back in.
Buffalo bill
Buffalo bill - Måned siden
dang I thought I had seen adjustable wrenches before...
Ion Racer
Ion Racer - Måned siden
Theyre not hard to rebuild
Just takes practice and a few tricks. Hope u greased the shit outta those upper ram mounts andrew
baby shoes for sale, worn soles.
When Andrew put his hard hat on I grabbed a hat in my room and put it on. Anyone else?
Geraldo Oliveira
Geraldo Oliveira - Måned siden
GOSTO MUITO DOS VIDEOS A GENTE APRENDE MUITO
Andrew Cran
Andrew Cran - Måned siden
Those have to be the biggest nylock nuts I've ever seen.
Lynn Stewart
Lynn Stewart - Måned siden
Andrew Excellent Video. Top Job
richardlwellington
richardlwellington - Måned siden
Yea the lever looks ghetto fabulous...
Steve T
Steve T - Måned siden
The guy who owned this machine before is kicking his azz after watching this video.
hak1985org
hak1985org - Måned siden
Andrew: "Lets just start unbolting stuff and see what happens" 
Me: that's the only approach I've ever used to fixing things!!
Tom tom
Tom tom - Måned siden
Well done, Andrew.
I'll remember how you greased the rubber seal of the new oil filter.
I always got an oily finger in the past, LOL!
Richard Clark
Richard Clark - Måned siden
Andrew, did you build those work tables in your shop? If so, would you consider doing a video about the process?
Andrew Camarata
Andrew Camarata - Måned siden
Yes, they are made out of 3" angle iron, rebar, sheet metal, and concrete.
Hilke Dors-Westerhof
Hilke Dors-Westerhof - Måned siden
were's the old dog at , has heeeye kick the bucket
fire surfer
fire surfer - Måned siden
FYI, https://degelman.com/pub/resources/manuals/cylinders/cylinder-repair/143367-Hyd-Cylinder-Repair-Guide.pdf
Shawn Green
Shawn Green - Måned siden
needs a battery and some kid to stop beating on it. :)
TIm Nash
TIm Nash - Måned siden
TIM from Canada I have watched this video almost 3/4 of the way through and what I am seeing from my analysis of the whole thing is the threads on the screw or screwed up this is what I see the threads on the bolts are screwed up
1crazypj
1crazypj - Måned siden
LOL, nothing changes.
Having to take apart brand new assemblies to repair the old stuff seems quite normal to me.
That's an interesting fork lift. Pretty sure the tilt function is to keep it level when going across sloping ground?
Usually there will be a lock pin hole (s) in boom so you can take all the pressure off lift cylinder pins?
I've rebuilt a couple of JCB 'Telehandlers' that got rolled over by people who should never have operated them in the first place and only got a little 'bounced around' for not wearing seat belt - that was a good point you made about it.
I spent a few years re-building hydraulic cylinders on everything from mini excavators to 3"diameter piston rods on larger stuff, being able to cut threads on piston rods saved company ????? thousands compared to the £175 an hour they had been paying (I'm British)
If you have spherical bearings there must be a very good reason for it as they are way more expensive than plain parallel bearings. You should have taken a better look at pivot shafts, probably 18" radius bearings?
BTW, if piston shafts are not bent or pitted, changing seal kits is pretty easy
More than once had to cut out pivot pins, make new ones and weld them back in correct alignment (even did a set for GKN construction division once, scissor lift pins just wore out and being a 'people carrier' had to meet various safety inspections
Leslie Q
Leslie Q - Måned siden
why didn't you give the cylinder rebuilder a call and ask about the tight fit? they could have told you what is stated in the comments.
Henrik Jonsson
Henrik Jonsson - Måned siden
Dont know but did you grease the joints? I think it also a kind of stiff because it is much small play in the joints when you bending one side off and maybe it is about take the load off from the arm that push the cylinder-joints. Good Work anyway!!!! Who dares wins!!!
orgcoast
orgcoast - Måned siden
If this was fixing "a few little things," I have to wonder what a major fix might be.
Bustin Ya
Bustin Ya - 2 måneder siden
Is there any equipment or tool Andrew doesn't have? I know were not suppose to be jealous of our neighbors stuff, but come on!
Paul Ice-Tate
Paul Ice-Tate - 2 måneder siden
Scene from the Borrowers at 42.00
Michel Barbeau
Michel Barbeau - 2 måneder siden
the old ladd i worked with often used a 1 inch drive air gun
1944chevytruck
1944chevytruck - 2 måneder siden
thanks 4 video. be kind.
J P
J P - 2 måneder siden
@28:00 My neighbor who runs a contracting business and repairs his own agricultural vehicles used to say, "If you have to use force to get it loose, you're probably doing something wrong."
Michael Delaney
Michael Delaney - 2 måneder siden
You are truly an artist, building your own replacement parts ................. a gift indeed
LuckySlevin7
LuckySlevin7 - 2 måneder siden
May I suggest the name: Forky McForkface
Xaltotun Great
Xaltotun Great - 2 måneder siden
The second cylinder 41:20 - LOL. This cylinder did put up a fight :-)). Andrew was so occupied by this work that he forgot to shave. Good video!
Neste